View DEH-1100_4086803.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pioneer corporation 4-1, meguro 1-chome, meguro-ku, tokyo 153-8654, japan pioneer electronics service inc. p.o.box 1760, long beach, ca 90801-1760 u.s.a. pioneer electronic [europe] n.v. haven 1087 keetberglaan 1, 9120 melsele, belgium pioneer electronics asiacentre pte.ltd. 253 alexandra road, #04-01, singapore 159936 c pioneer corporation 1999 k-zza. nov. 1999 printed in japan order no. crt2433 high power cd player with fm/am tuner DEH-1100 x1m/uc service manual contents 1. safety information ............................................2 2. exploded views and parts list .......................2 3. block diagram and schematic diagram .....8 4. pcb connection diagram ................................26 5. electrical parts list ........................................36 6. adjustment..........................................................41 7. general information .......................................45 7.1 diagnosis ........................................................45 7.1.1 test mode ..............................................45 7.1.2 disassembly .........................................48 7.2 parts .................................................................52 7.2.1 ic................................................................52 7.2.2 display ....................................................58 7.3 operational flow chart ...........................59 8. operations and specifications.....................60 deh-11 x1m/uc DEH-1100/x1m/uc - this service manual should be used together with the following manual(s): model no. order no. mech. module remarks cx-958 crt2423 s8.1 cd mech. module:circuit description, mech.description, disassembly
2 DEH-1100,11 - cd player service precautions 1. for pickup unit(cxx1285) handling, please refer to"disassembly"(see page 48). during replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a short pin). 2. during disassembly, be sure to turn the power off since an internal ic might be destroyed when a con- nector is plugged or unplugged. 3. please checking the grating after changing the ser- vice pickup unit(see page 43). 2. exploded views and parts list 2.1 packing 14 1 10 12 13 15 11 5 9 2 8 7 6 4 3 caution this service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. if you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so and refer the repair to a qualified service technician. w arning this product contains lead in solder and certain electrical parts contain chemicals which are known to the state of california to cause cancer, birth defects or other reproductive harm. health & safety code section 25249.6 - proposition 65 1. safety information
3 DEH-1100,11 1 cord assy cde6124 2 spring cbh1650 3 screw cba1002 * 4 polyethylene bag ceg-127 5 screw crz50p090fmc 6 screw trz50p080fmc * 7 polyethylene bag ceg-158 8 handle cnc5395 9 bush cnv3930 10 polyethylene bag ceg1173 11-1 polyethylene bag ceg1116 11-2 owners manual crd3133 11-3 installation manual crd3134 * 11-4 card ary1048 12 carton see contrast table(2) 13 contain box see contrast table(2) 14 protector chp2243 15 protector chp2244 mark no. description part no. mark no. description part no. (1) packing section parts list note: - parts marked by ??are generally unavailable because they are not in our master spare parts list. - screws adjacent to ? mark on the product are used for disassembly. part no. mark no. symbol and description DEH-1100/x1m/uc deh-11/x1m/uc 12 carton chg3953 chg3954 13 contain box chl3953 chl3954 (2) contrast table DEH-1100/x1m/uc and deh-11/x1m/uc are constructed the same except for the following: - owner's manual, installation manual model part no. language DEH-1100/x1m/uc crd3133 english, french, spanish deh-11/x1m/uc crd3134
4 DEH-1100,11 2.2 exterior
5 DEH-1100,11 1 screw bmz26p120fmc 2 screw bsz26p060fmc 3 screw bsz30p060fmc 4 screw bsz30p120fmc 5 cord assy cde6124 6 cable cde6160 7 fuse(10a) cek1136 8 cd mechanism module(s8.1) cxk5203 9 cover cnc8367 10 holder cnc8884 11 spacer cnm4913 12 insulator cnm6224 13 insulator cnm6386 14 panel cns5132 15 tuner amp assy cwm6769 16 screw asz26p080fmc 17 screw bpz26p080fmc 18 screw bsz26p160fmc 19 fm/am tuner unit cwe1501 20 holder cnc7532 21 pin jack(cn301) ckb1041 22 terminal(cn403) ckf1059 23 connector(cn901) ckm1299 24 connector(cn601) cks3581 25 connector(cn605) cks3838 26 antenna jack(cn402) ckx1056 27 holder cnc7533 28 holder cnc8041 29 holder cnc8043 30 holder cnc8588 31 insulator cnm5967 32 heat sink cnr1506 33 holder unit cxb2687 34 case unit cxb4033 35 screw bpz20p080fmc 36 button(+, -) cac6273 37 button(1-6) cac6275 38 button(b, a, cross) cac6276 39 button(eject) cac6277 40 button(source) cac6495 41 cover cnm6434 42 holder cnv5963 43 keyboard unit see contrast table(2) 44 lcd(lcd1801) caw1560 45 connector(cn1801) cks3580 46 holder cnc8517 47 rubber cnv5954 48 lighting conductor cnv5965 49 rubber cnv5966 50 grille unit see contrast table(2) 51 chassis unit cxb4625 52 screw iss26p055fuc 53 ic(ic302) tda7384 54 transistor(q904, 981) 2sd2396 (1) exterior section parts list mark no. description part no. mark no. description part no. part no. mark no. symbol and description DEH-1100/x1m/uc deh-11/x1m/uc 43 keyboard unit cwm6783 cwm6782 50 grille unit cxb4619 cxb4620 (2) contrast table DEH-1100/x1m/uc and deh-11/x1m/uc are constructed the same except for the following:
6 DEH-1100,11 2.3 cd mechanism module
7 DEH-1100,11 mark no. description part no. mark no. description part no. 1 control unit cwx2411 2 connector(cn802) cks2192 3 connector(cn801) cks2193 4 connector(cn701) cks2773 5 connector(cn101) cks3486 6 screw bmz20p030fmc 7 screw bsz20p040fmc 8 screw(m2x3) cba1077 9 screw(m2x5) eba1028 10 screw cba1243 11 screw(m2x4) cba1362 12 washer cbf1037 13 washer cbf1038 14 washer cbf1060 15 16 spring cbh2079 17 spring cbh2117 18 spring cbh2314 19 spring cbh2110 20 spring cbh2282 21 spring cbh2318 22 23 spring cbh2324 24 spring cbh2118 25 spring cbh2161 26 spring cbh2163 27 spring cbh2189 28 spring cbh2249 29 spring cbh2260 30 spring cbh2262 31 bracket cnc8568 32 spring cbl1369 33 connector cde5531 34 connector cde5532 35 shaft cla3304 36 screw(m2.6x6) cba1458 37 frame cnc8565 38 frame cnc8749 39 lever cnc7546 40 arm cnc8663 41 bracket cnc8567 42 43 spacer cnm3315 44 sheet cnm6659 45 46 47 ball cnr1189 48 belt cnt1086 49 roller cnv4509 50 arm cnv6037 51 arm cnv5247 52 arm cnv5248 53 arm cnv5249 54 guide cnv5254 55 guide cnv5255 56 gear cnv5257 57 gear cnv5256 58 guide cnv6176 59 damper cnv6174 60 arm cnv6096 61 arm cnv6031 62 arm cnv6211 63 guide cnv6012 64 guide cnv5510 65 66 guide cnv5751 67 clamper cnv6013 68 gear cnv5813 69 motor unit(m1) cxb2190 70 screw unit cxb4726 71 chassis unit cxb4797 72 gear unit cxb4728 73 arm unit cxb4729 74 motor unit(m2) cxb2195 75 lever unit cxb4730 76 arm unit cxb4731 77 motor unit(m3) cxb2562 78 arm unit cxb4732 79 bracket unit cxb4795 80 screw jfz20p025fmc 81 screw jgz17p025fzk 82 washer ye20fuc 83 pickup unit(service)(p8) cxx1285 84 screw ims26p030fmc * 85 pcb cnx2982 86 photo-transistor(q1, 2) cpt230sx-tu 87 damper cnv6175 88 rack cnv6014 89 spring cbh2315 - cd mechanism module section parts list
8 DEH-1100,11 1 23 4 1 234 d c b a 3. block diagram and schematic diagram 3.1 block diagram ant1 tv ant2 tv rf tv ic 3 br9010fv am 2nd if 450khz m m m ld md hologram unit focus act tracking act ld+ md fo+ to+ 14 5 4 3 spindle motor carriage motor loading motor 1 2 3 4 3 1 2 select sense disc sense e cn801 cn802 d803 d802 d801 vd s802 clamp 6 5 11 22 23 21 1 28 21 cdload cdejet cont ejtsns dscsns clamp cd5von vdcont vdd ic 701 ba05sfp in +5v regulator 2 4 1 vd q981 q982 b.u antenna cn402 a b 27 28 fm front end q3 q201 q204 am rf fm/am 1st if 10.7mhz t51 q51 cf51 cf52 cf53 mixer.if amp det ic 1 pml002a 38 39 42 44 46 63 32 19 46 6 21 18 ldet comp 34 33 41 44 11 12 13 69 70 54 78 65 71 75 74 61 57 55 45 33 35 22 22 25 10 14 12 15 16 13 2 3 4 cf202 vdd locl vcc q411 vcc vdd di/do ce2 ck ce1 sl fmsd pce2 ck pce1 pck sd pdio nl1 nl2 eeprom 5 6 4 3 ic 2 pm4008a fm mpx d q101 cn101 fop top a+c/f b+d/e 98 ld l_out pd home 97 24 23 39 x201 td/fd sd/md rf-amp, dsp, servo, dac ic 201 upd63711gc 16 cn701 cn605 17 1 8 24 cdl ic 301 ba5985fm s801 home 12 16 18 11 14 13 10 9 sop top fop som cop com lop lom fwd rev mute 25 24 cd driver 718 19 20 14 3 2 4 clamp dinc ejtd cdload ejet cont q202 32 pd tuner amp assy fm/am tuner unit control unit pickup unit(service)(p8) photo unit(s8) 4 vd cd5von
9 DEH-1100,11 5 6 78 5 6 7 8 d c b a kydt dpdt lcd driver ic 1801 pd6293a 3 4 5 3 4 5 key matrix sd sl tunpce tunpck tunpce2 tunpdo locl in1 in2 6 76 14 13 48 12 67 2 3 system controller ic 601(1/2) pe5091a vst vck vdt b.u vdd q903 b.u backup fl fl+ rl rl+ acc 2 1 9 11 10 12 4 electronic volume/ source selector ic 301 sn761029dl system controller ic 601(2/2) pe5091a asens 63 bsens 64 syspw 42 mute 44 kydt 8 dpdt 9 reset 60 swvdd 41 fout 19 rout 20 power amp ic 302 tda7384 14 12 22 4 5 3 21 23 fl mute stby rl b.u bsens asens q902 q351 mute c keyboard unit cn1801 cn601 lcd 22 23 x1801 20 18 q650 reset ic 602 s 80834any vdd 12 syspw back up gnd fl fl+ rl rl+ 5 b.remote fuse 10a gnd acc b.remote cd5von 31 34 23 80 79 27 22 35 vdcont clamp dscsns ejtsns cdload cdeject cont tunpdi 11 pdio vst/ vck/ vdt q901 vdd vdd vlcd 50 10 q346 cn301 rear l ch q353 q942 q941
10 DEH-1100,11 1 23 4 1 234 d c b a 3.2 overall connection diagram(guide page) note: when ordering service parts, be sure to refer to ?xploded views and parts list?or ?lectrical parts list? a-a a-b a-a a-a a-b a-b a-b a-b a-a a-a large size sch diagram guide page detailed page a a-a dsp-201m-s00b c499 103 272 272 183 183 162 162 104 4.194304mhz css1023 104 433 822 682 r699 0r0 150 150 fm(100%):-19.5dbs am (30%):-30dbs cd:+4. fm(100%):-19 am (30%):-30 fm/am tuner unit for resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: ex. *resistors code practical value 123 12k ohms 103 10k ohms *capacitors code practical value 103 0.01 f 101/10 100 f/10v the > mark found on some component parts indicates the importance of the safety factor of the part. therefore, when replacing, be sure to use parts of identical designation. symbol indicates a resistor. no differentiation is made between chip resistors and discrete resistors. note : symbol indicates a capacitor. no differentiation is made between chip capacitors and discrete capacitors. r system controller keyboard unit b c
11 DEH-1100,11 5 6 78 5 6 7 8 d c b a a-b a 332/16 600 h > (b2) cek1136 4.1dbs 9.5dbs 0dbs cd:+10.1dbs fm(100%):+3.5dbs am (30%):-7dbs cd:+10.1dbs fm(100%):+3.5dbs am (30%):-7dbs cd:+36.1dbs fm(100%):+29.5dbs am (30%):+19dbs cd:+4.1dbs cd mechanism module power amp source selector/ e.vol reset vd regulator tuner amp assy a a d
12 DEH-1100,11 1 23 4 1 234 d c b a a-a a-a a-b dsp-201m-s00b c499 103 272 272 183 183 162 162 104 4.194304mhz css1023 150 150 fm(100%):-19.5dbs am (30%):-30dbs cd:+4.1dbs fm(100%):-19.5dbs am (30%):-30dbs fm/am tuner unit source e.vol b 1
13 DEH-1100,11 5 6 78 5 6 7 8 d c b a a-a a-a a-b 104 433 822 682 r699 0r0 150 150 cd mechanism module for resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: ex. *resistors code practical value 123 12k ohms 103 10k ohms *capacitors code practical value 103 0.01 f 101/10 100 f/10v the > mark found on some component parts indicates the importance of the safety factor of the part. therefore, when replacing, be sure to use parts of identical designation. symbol indicates a resistor. no differentiation is made between chip resistors and discrete resistors. note : symbol indicates a capacitor. no differentiation is made between chip capacitors and discrete capacitors. reset system controller keyboard unit c d 2
14 DEH-1100,11 1 23 4 1 234 d c b a a-a a-b a-b 332/16 600 h > cek1136 .1dbs 9.5dbs 0dbs cd:+10.1dbs fm(100%):+3.5dbs am (30%):-7dbs cd:+10.1dbs fm(100%):+3.5dbs am (30%):-7dbs cd:+36.1dbs fm(100%):+29.5dbs am (30%):+19dbs power amp source selector/ e.vol tuner amp assy a a 1
15 DEH-1100,11 5 6 78 5 6 7 8 d c b a a-b a-a a-b 600 h (b2) cd:+4.1dbs cd mechanism module reset vd regulator d 2
16 DEH-1100,11 1 23 4 1 234 d c b a b kv1410(23) mark none f0 f65 f125 a0 a74 a125 band fm fm fm am am am input level 0dbf 65dbf 125dbf 0db 74db 125db dan217u dan217u 3.3 fm/am tuner unit b a fm/am tuner unit
17 DEH-1100,11 5 6 78 5 6 7 8 d c b a kv1410(23) b
18 DEH-1100,11 1 23 4 1 234 d c b a 3.4 keyboard unit c keyboard unit c lcd driver, key controller pd6293a caw1560
19 DEH-1100,11 5 6 78 5 6 7 8 d c b a c loud clk local bsm DEH-1100/x1m/uc deh-11/x1m/uc il1801-1804 cel1547(14v 40ma) cel1638(14v 40ma) a cn601
DEH-1100,11 1 23 4 1 234 d c b a ba05sfp (service)(p8) pickup unit photo unit(s8) control unit spindle motor q2 cpt230sx-tu q1 cpt230sx-tu m3 cxb2562 carriage motor m1 cxb2190 m2 cxb2195 loading motor rf-amp, se 5v regulator cd driver cn101 cn802 cn801 3.5 cd mechanism module e d e d 20
DEH-1100,11 5 6 78 5 6 7 8 d c b a mp, servo, dsp, dac, lpf switches: control unit s801 : home switch.....on-off s802 : clamp switch....on-off the underlined indicates the switch position. cn701 a cn605 d 21
22 DEH-1100,11 1 rfi 0.5v/div. 0.5 s/div. normal mode: play 1 ch1: rfi 1v/div. 2 ch2: mirr 5v/div. test mode: tracking open 0.5ms/div. 1 ch1: rfi 1v/div. 2 ch2: mirr 5v/div. normal mode: the defect part passes 800 m 0.5ms/div. 3 ch1: fd 0.5v/div. 4 ch2: fo+ 2v/div. test mode: no disc, focus close 0.2s/div. 3 ch1: fd 0.5v/div. 5 ch2: fok 2v/div. normal mode: focus close 0.2s/div. 6 ch1: fe 0.5v/div. 7 ch2: xsi 2v/div. normal mode: focus close 1ms/div. refo 8 ch1: te 0.5v/div. 9 ch2: td 0.5v/div. test mode: 32 tracks jump (fwd) 0.5ms/div. 8 ch1: te 0.5v/div. 9 ch2: td 0.5v/div. test mode: single jump (fwd) 0.5ms/div. 8 ch1: te 0.5v/div. 9 ch2: td 0.5v/div. test mode: 100 tracks jump (fwd) 5ms/div. 6 ch1: fe 0.1v/div. 3 ch2: fd 0.2v/div. normal mode: play 20ms/div. 3 ch1: fd 0.5v/div. 0 ch2: md 1v/div. normal mode: focus close (12cm) 0.5s/div. 3 ch1: fd 0.5v/div. 0 ch2: md 1v/div. normal mode: focus close (8cm) 0.5s/div. refo refo refo refo refo refo gnd refo refo refo refo refo refo refo refo refo refo refo refo - waveforms note:1. the encircled numbers denote measuring pointes in the circuit diagram. 2. reference voltage refo:2.5v refo refo refo refo
23 DEH-1100,11 8 ch1: te 0.2v/div. 9 ch2: td 0.2v/div. normal mode: play 8 ch1: te 0.5v/div. ! ch2: sd 0.5v/div. test mode: 100 tracks jump(fwd) 5ms/div. 0 md 0.5v/div. 0.1s/div. normal mode: play (12cm) 0 md 1v/div. 10ms/div. normal mode: long search (12cm) @ efm 1v/div. 5 s/div. normal mode: play 8 ch1: te 1v/div. # ch2: tec 1v/div. test mode: focus close tracking open 2ms/div. 8 ch1: te 0.5v/div. 6 ch2: fe 0.5v/div. normal mode: agc after focus close 0.2s/div. $ plck 2v/div. 0.5 s/div. normal mode: play 20ms/div. % scko 2v/div. 1 s/div. normal mode: play ^ dout 2v/div. 10 s/div. normal mode: play & lrck 2v/div. 20 s/div. normal mode: play * vd 5v/div. 50ms/div. normal mode: no disc gnd refo refo gnd refo refo refo refo refo refo refo refo refo gnd refo gnd refo gnd refo gnd refo
24 DEH-1100,11 ( ch1: r out 1v/div. ) ch2: l out 1v/div. normal mode: play (1khz 0db) 6 ch1: fe 0.2v/div. 3 ch2: fd 0.5v/div. normal mode: during agc 1ms/div. 8 ch1: te 0.2v/div. 9 ch2: td 0.5v/div. normal mode: during agc 1 ch1: rfi 1v/div. ? ch2: hold 5v/div. normal mode: the defect part passes 800 m(b.d) 0.2ms/div. 1ms/div. 0.5ms/div. 3 ch1: fd 0.5v/div. ? ch2: hold 5v/div. normal mode: the defect part passes 800 m(b.d) 0.5ms/div. 9 ch1: td 0.1v/div. ? ch2: hold 5v/div. normal mode: the defect part passes 800 m(b.d) 0.5ms/div. refo refo refo refo refo refo refo refo refo refo refo refo
25 DEH-1100,11
26 DEH-1100,11 1 23 4 1 234 d c b a 4. pcb connection diagram 4.1 tuner amp assy note for pcb diagrams 1. the parts mounted on this pcb include all necessary parts for several destination. for further information for respective destinations, be sure to check with the schematic dia- gram. 2. viewpoint of pcb diagrams a capacitor connector p.c.board chip part side a side b cord assy cn701 d c cn1801 a tuner amp assy
27 DEH-1100,11 5 6 78 5 6 7 8 d c b a a side a b
28 DEH-1100,11 1 23 4 1 234 d c b a a a tuner amp assy
29 DEH-1100,11 5 6 78 5 6 7 8 d c b a a side b
30 DEH-1100,11 1 23 4 1 234 d c b a 4.2 fm/am tuner unit side a b fm/am tuner unit a b
31 DEH-1100,11 1 2 34 1 2 3 4 d c b a side b b fm/am tuner unit b
32 DEH-1100,11 1 23 4 1 234 d c b a 4.3 keyboard unit c c side a keyboard unit + loud 1 2 3 4 5 6 local clock bsm band eject ' ] [ ' audio source/off -
33 DEH-1100,11 1 2 34 1 2 3 4 d c b a c c side b keyboard unit a cn601
34 DEH-1100,11 1 23 4 1 234 d c b a 4.4 cd mechanism module control unit home m1 carriage motor m2 loading motor m3 spindle motor pickup unit(service)(p8) cn802 cn605 3 2 1 photo unit(s8) side a a d e d d e e
35 DEH-1100,11 1 2 34 1 2 3 4 d c b a clamp side b control unit d d
36 DEH-1100,11 5. electrical parts list notes: - parts whose parts numbers are omitted are subject to being not supplied. - the part numbers shown below indicate chip components. chip resistor rs1/ _ s ___ j,rs1/ __ s ___ j chip capacitor (except for cqs.....) cks....., ccs....., cszs..... =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- unit number : cwm6769 unit name : tuner amp assy miscellaneous ic 301 ic sn761029dl ic 302 ic tda7384 ic 601 ic pe5091a ic 602 ic s-80834any q 346 transistor rn1610 q 351 transistor dtc114ek q 353 transistor dta124ek q 411 transistor 2sc2412k q 650 transistor 2sa1037k q 901 transistor 2sc2412k q 902 transistor 2sc2412k q 903 transistor 2sd1859 q 904 transistor 2sd2396 q 905 transistor 2sb1243 q 906 transistor dtc114ek q 941 transistor 2sb1243 q 942 transistor dtc114ek q 981 transistor 2sd2396 q 982 transistor rn46a1 d 901 diode hzs7l(c2) d 902 diode s5688g d 903 diode s5688g d 904 diode hzs7l(a1) d 905 diode s5688g d 906 diode hzs6l(b2) d 907 diode hzs9l(b3) d 941 diode s5688g d 942 diode s5688g d 981 diode hzs9l(b1) l 401 ferri-inductor lau4r7k l 402 ferri-inductor lau2r2k l 403 inductor lau100k l 610 ferri-inductor lau101k l 611 ferri-inductor lau2r2k l 650 ferri-inductor lau2r2k l 901 choke coil 600h cth1221 th 601 thermistor ccx1031 x 610 crystal resonator 4.194304mhz css1023 ar 946 arrester dsp-201m-s00b fm/am tuner unit cwe1501 resistors r 310 rd1/4pu222j r 311 rd1/4pu222j r 312 rs1/10s272j r 313 rs1/10s272j r 314 rs1/10s151j r 315 rs1/10s151j r 316 rs1/10s0r0j r 317 rs1/10s121j r 318 rd1/4pu104j r 319 rd1/4pu104j r 320 rs1/10s121j r 321 rs1/10s101j r 322 rs1/10s101j r 342 rs1/8s821j r 343 rs1/8s821j r 344 rs1/10s223j r 345 rs1/10s223j r 352 rs1/10s103j r 353 rs1/10s103j r 354 rs1/10s331j r 360 rd1/4pu153j r 411 rs1/10s681j r 412 rs1/10s681j r 413 rs1/10s681j r 414 rs1/10s103j r 415 rs1/8s681j r 416 rd1/4pu473j r 417 rd1/4pu472j r 418 rs1/10s473j r 419 rs1/10s473j r 420 rs1/10s473j r 421 rs1/10s473j r 422 rs1/10s473j r 423 rs1/10s681j r 424 rs1/10s681j r 425 rs1/10s393j r 427 rs1/10s222j r 428 rs1/10s222j r 460 rs1/10s272j r 461 rs1/10s272j r 464 rs1/10s162j r 465 rs1/10s162j r 468 rs1/10s0r0j r 469 rs1/10s0r0j r 610 rd1/4pu822j r 611 rs1/10s433j r 614 rs1/8s0r0j r 619 rs1/10s682j r 620 rn1/10se2202d r 622 rd1/4pu222j r 623 rd1/4pu222j r 624 rs1/10s473j r 625 rs1/10s473j r 626 rs1/10s473j r 627 rd1/4pu473j r 628 rd1/4pu222j r 629 rs1/10s473j r 630 rs1/10s822j r 649 rs1/8s222j r 650 rs1/8s222j =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- a
37 DEH-1100,11 r 651 rs1/8s222j r 655 rs1/10s103j r 656 rs1/10s103j r 657 rd1/4pu102j r 658 rd1/4pu102j r 660 rs1/10s1r0j r 681 rd1/4pu681j r 682 rs1/10s102j r 683 rd1/4pu102j r 684 rs1/10s102j r 699 rs1/10s0r0j r 725 rs1/10s0r0j r 901 rs1/10s473j r 902 rd1/4pu103j r 903 rd1/4pu103j r 904 rs1/10s473j r 905 rs1/10s102j r 906 rs1/10s473j r 907 rs1/10s473j r 908 rs1/10s472j r 909 rd1/4pu103j r 911 rs1/10s122j r 912 rd1/4pu103j r 914 rd1/4pu152j r 916 rs1/10s221j r 918 rs1/10s1r0j r 941 rd1/4pu472j r 942 rd1/4pu152j r 981 rs1/10s472j r 982 rs1/10s222j r 983 rd1/4pu221j r 984 rd1/4pu221j capacitors c 310 cksqyb105k16 c 311 cksqyb104k16 c 312 ceja2r2m50 c 313 cksqyb105k16 c 314 cksyb104k16 c 315 cksqyb102k50 c 316 cksqyb102k50 c 317 ceja100m16 c 318 ceja100m16 c 319 cksqyb822k50 c 320 cksqyb822k50 c 321 ceal1r0m50 c 322 ceja1r0m50 c 323 cksqyb183k50 c 324 cksqyb183k50 c 325 cksqyb104k16 c 326 cksqyb104k16 c 327 cksqyb104k16 c 328 cksqyb104k16 c 329 ceja2r2m50 c 330 ceja4r7m50 c 332 cksqyb473k16 c 333 cksqyb104k16 c 334 cksqyb104k16 c 335 ceal470m10 c 340 ceal2r2m50 c 341 ceja2r2m50 c 350 ceja330m10 c 361 ceja2r2m50 c 362 cksyb225k16 c 363 ceja100m16 c 364 cksyb474k16 c 365 cksqyb474k16 c 366 cksyb474k16 c 367 cksqyb474k16 c 368 cksqyb474k16 c 369 cksyb474k16 c 370 cksqyb474k16 c 371 cksyb474k16 c 372 cksqyb225k10 c 390 cksqyb104k16 c 391 3300f/16v cch1368 c 411 cksqyb223k25 c 412 cksqyb223k25 c 413 cksqyb102k50 c 414 ceja220m10 c 415 cksqyb473k16 c 416 ceal101m10 c 417 cksqyb472k50 c 462 cksqyb183k25 c 463 cksqyb183k25 c 490 cksqyb103k50 c 499 cksqyb103k50 c 611 cksqyb104k16 c 612 ceja4r7m35 c 613 cksqyb473k16 c 614 cksqyb102k50 c 628 ccsqch150j50 c 629 ccsqch150j50 c 630 cksqyb473k16 c 631 ceal2r2m50 c 650 cksqyb104k16 c 901 ceja101m10 c 902 cksqyb473k16 c 903 470f/16v cch1331 c 904 cksqyb473k16 c 905 330f/16v cch1326 c 906 cksqyb103k50 c 907 ceja101m16 c 941 cksqyb473k16 c 981 ceja101m10 c 982 cksqyb102k50 c 983 cksqyb473k16 unit number : cwe1501 unit name : fm/am tuner unit miscellaneous ic 1 ic pml002a ic 2 ic pm4008a ic 3 ic br9010fv q 1 transistor 2sc4081 q 2 transistor dtc124eu q 3 fet 3sk263 q 51 transistor 2sc4081 q 201 fet 2sk932 q 202 transistor dtc124eu q 204 transistor 2sc4081 d 1 diode kv1410(23) d 2 diode 1sv248 d 6 diode kv1410(23) d 201 diode dan217u d 202 diode dan217u d 903 diode kv1410(23) d 904 diode svc253 l 1 coil ctc1155 l 3 inductor lctb1r5k2125 l 4 coil ctc1155 =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- b
38 DEH-1100,11 l 201 inductor lctb330k1608 l 202 inductor ctf1287 l 203 inductor lcta121j3225 l 901 coil ctc1154 l 902 inductor lcta3r3j3225 l 904 inductor lctbr47k1608 l 905 inductor lctbr47k1608 t 51 coil cte1132 cf 51 ceramic filter ctf1442 cf 52 ceramic filter ctf1442 cf 53 ceramic filter ctf1442 cf 202 ceramic filter ctf1348 x 901 crystal resonator 10.250mhz css1432 resistors r 1 rs1/16s183j r 2 rs1/16s103j r 5 rs1/16s0r0j r 7 rs1/16s273j r 8 rs1/16s473j r 9 rs1/16s223j r 10 rs1/16s473j r 11 rs1/16s221j r 12 rs1/16s103j r 13 rs1/16s104j r 16 rs1/16s223j r 17 rs1/16s221j r 18 rs1/16s221j r 19 rs1/16s473j r 20 rs1/16s470j r 31 rs1/16s0r0j r 51 rs1/16s470j r 52 rs1/16s103j r 53 rs1/16s103j r 54 rs1/16s331j r 55 rs1/16s331j r 56 rs1/16s560j r 57 rs1/16s560j r 58 rs1/16s102j r 59 rs1/16s225j r 60 rs1/16s133j r 61 rs1/16s433j r 101 rs1/16s333j r 102 rs1/16s103j r 103 rs1/16s333j r 104 rs1/16s562j r 106 rs1/16s0r0j r 108 rs1/16s0r0j r 110 rs1/16s154j r 111 rs1/16s273j r 113 rs1/16s222j r 114 rs1/16s333j r 115 rs1/16s334j r 116 rs1/16s473j r 202 rs1/16s472j r 203 rs1/16s225j r 204 rs1/16s102j r 205 rs1/16s220j r 206 rs1/16s471j r 208 rs1/16s104j r 209 rs1/16s104j r 210 rs1/16s563j r 213 rs1/16s223j r 251 rs1/16s225j r 902 rs1/16s103j r 904 rs1/16s473j r 907 rs1/16s103j r 908 rs1/16s681j r 909 rs1/16s473j r 914 rs1/16s562j capacitors c 1 ccsqch4r0c50 c 6 cksqyb105k10 c 8 cksryb222k50 c 10 ccsrch220j50 c 11 ccsrch150j50 c 12 ccsrch8r0d50 c 14 ccsrcj3r0c50 c 15 cksryb103k50 c 16 cksryb222k50 c 17 cksryb222k50 c 18 ccsrcj3r0c50 c 19 cksryb103k50 c 20 cksryb103k50 c 21 cksryb103k50 c 24 cksqyb334k16 c 26 cksryb472k50 c 30 ccsrch220j50 c 32 ccsrch470j50 c 35 cksryb103k50 c 51 cksryb103k50 c 52 cksryb473k16 c 53 ccsrck2r0c50 c 54 cksryb103k50 c 55 cksryb104k16 c 56 cksryb104k16 c 58 cksqyb224k16 c 101 cealnp100m10 c 102 ccsrch151j50 c 103 cksryb473k16 c 105 cksryb682k25 c 106 cealr68m50 c 107 cksryb103k50 c 108 cksqyb474k16 c 109 cksqyb474k16 c 110 cksryb104k16 c 111 cksryb104k16 c 112 cksryb104k16 c 113 cksryb123k25 c 114 ceal220m6r3 c 115 cksryb473k16 c 116 ceal2r2m50 c 117 cksryb102k50 c 120 cksryb183k25 c 121 cksryb332k50 c 122 cksryb562k25 c 123 cksryb681k50 c 125 cksryb103k50 c 126 cksryb103k50 c 127 ceal2r2m50 c 128 cksryb103k50 c 201 ccsrch471j50 c 202 ccsrch100d50 c 203 cksryb104k16 c 204 cksryb332k50 c 205 cksryb103k50 c 206 cksryb104k16 c 207 cksryb473k16 c 208 ccsrch560j50 c 209 ceal470m6r3 c 210 cksryb103k50 =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ -------------------------
39 DEH-1100,11 c 211 cksryb103k50 c 212 ccsrch101j50 c 215 cksryb223k25 c 216 cksqyb334k16 c 217 cksryb103k50 c 219 cksqyb105k10 c 220 cksryb104k16 c 221 cksryb473k16 c 222 cksqyb334k16 c 223 cksqyb474k16 c 224 cksryb104k16 c 225 cksryb272k50 c 226 cksryb682k25 c 902 ccsrch270j50 c 904 cksryb223k25 c 905 cksryb103k50 c 906 ccsrth100d50 c 907 ccsrth150j50 c 909 ccsrth100d50 c 910 cksryb332k50 c 912 cksqyb474k16 c 913 cksryb223k25 c 914 cksryb682k25 c 915 cksqyb223k25 c 916 cksqyb474k16 c 917 cksyb475k10 c 918 cksryb223k25 c 919 cksqyb225k10 c 920 ccsrch270j50 c 921 ccsrch270j50 c 922 cksyb105k16 c 923 cksryb103k50 unit number : cwm6783(DEH-1100) : cwm6782(deh-11) unit name : keyboard unit miscellaneous ic 1801 ic pd6293a x 1801 ceramic resonator 4.97mhz css1422 il 1801 lamp 14v 40ma(DEH-1100) cel1547 il 1801 lamp 14v 40ma(deh-11) cel1638 il 1802 lamp 14v 40ma(DEH-1100) cel1547 il 1802 lamp 14v 40ma(deh-11) cel1638 il 1803 lamp 14v 40ma(DEH-1100) cel1547 il 1803 lamp 14v 40ma(deh-11) cel1638 il 1804 lamp 14v 40ma(DEH-1100) cel1547 il 1804 lamp 14v 40ma(deh-11) cel1638 lcd1801 lcd caw1560 resistors r 1801 rs1/8s222j r 1802 rs1/8s222j r 1803 rs1/10s471j r 1804 rs1/10s471j r 1805 rs1/10s471j r 1806 rs1/10s471j capacitors c 1801 cksqyb103k25 unit number : cwx2411 unit name : control unit miscellaneous ic 201 ic upd63711gc ic 301 ic ba5985fm ic 701 ic ba05sfp q 101 transistor 2sb1132 d 801 led cl200irx d 802 led cl200irx x 201 ceramic oscillator 16.934mhz css1456 s 801 spring switch(home) csn1051 s 802 spring switch(clamp) csn1052 resistors r 101 rs1/8s120j r 102 rs1/8s100j r 103 rs1/16s222j r 201 rs1/16s104j r 202 rs1/16s103j r 203 rs1/16s393j r 204 rs1/16s103j r 205 rs1/16s103j r 206 rs1/16s182j r 207 rs1/16s123j r 302 rs1/16s153j r 303 rs1/16s103j r 501 rs1/16s102j r 502 ra4c681j r 601 rs1/16s102j r 602 rs1/16s102j r 605 rs1/16s0r0j r 606 rs1/16s0r0j r 801 rs1/8s751j r 803 rs1/8s751j r 902 rs1/16s0r0j r 906 rs1/16s0r0j capacitors c 101 ccsrch102j25 c 102 cksryb104k16 c 103 cev101m6r3 c 104 cev470m6r3 c 105 cksqyb334k16 c 106 cksqyb334k16 c 107 cksqyb334k16 c 201 cksryb104k16 c 202 cksryb471k50 c 203 cksryb104k16 c 205 cev101m6r3 c 206 cksryb104k16 c 207 cksryb104k16 c 208 cksryb104k16 c 209 cksryb104k16 c 210 cksryb332k50 c 211 cksryb104k16 c 212 cksryb104k16 c 213 cksryb392k50 c 214 cksryb104k16 c 215 cksryb104k16 c 216 ccsrcj3r0c50 c 217 ccsrch270j50 c 218 cksryb104k16 c 219 ccsrch181j50 =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ ------------------------- d c
40 DEH-1100,11 c 220 ccsrch510j50 c 221 cksryb682k25 c 222 cev220m6r3 c 223 cksryb103k25 c 224 cksryb224k10 c 301 cev101m10 c 603 ccsqsl152j50 c 604 ccsqsl152j50 c 702 10f/10v cch1349 c 703 cksqyb334k16 unit number : unit name : photo unit(s8) q 1 photo-transistor cpt230sx-tu q 2 photo-transistor cpt230sx-tu miscellaneous parts list pickup unit(service)(p8) cxx1285 m 1 motor unit(carriage) cxb2190 m 2 motor unit(loading) cxb2195 m 3 motor unit(spindle) cxb2562 fuse(10a) cek1136 e =====circuit symbol and no.===part name part no. --- ------ ------------------------------------------ -------------------------
41 DEH-1100,11 1) precautions this unit uses a single power supply (+5v) for the reg- ulator. the signal reference potential, therefore, is connected to refo(approx. 2.5v) instead of gnd. if refo and gnd are connected to each other by mis- take during adjustments, not only will it be impossi- ble to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. to avoid this, take special note of the fol- lowing. do not connect the negative probe of the measuring equipment to refo and gnd together. it is especially important not to connect the channel 1 negative probe of the oscilloscope to refo with the channel 2 negative probe connected to gnd. since the frame of the measuring instrument is usual- ly at the same potential as the negative probe, change the frame of the measuring instrument to floating sta- tus. if by accident refo comes in contact with gnd, immediately switch the regulator or power off. always make sure the regulator is off when connect- ing and disconnecting the various filters and wiring required for measurements. before proceeding to further adjustments and mea- surements after switching regulator on, let the player run for about one minute to allow the circuits to stabi- lize. since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the sys- tem when making adjustment. disc detection during loading and eject operations is performed by means of a photo transistor in this unit.consequently, if the inside of the unit is exposed to a strong light source when the outer casing is removed for repairs or adjustment, the following mal- functions may occur. *during play, even if the eject button is pressed,the disc will not be ejected and the unit will remain in the play mode. *the unit will not load a disc. when the unit malfunctions this way, either re-posi- tion the light source, move the unit or cover the photo transistor. 2) test mode this mode is used for adjusting the cd mechanism module of the device. test mode starting procedure reset while pressing the 4 and 6 keys together. test mode cancellation switch acc, back-up off. after pressing the eject key, do not press any other key until the disk is completely ejected. if the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses). jump operation of trs other than 100tr continues after releasing the key. crg move and 100tr jump operations are brought into the tracking close sta- tus when the key is released. powering off/on resets the jump mode to 1tr , and the automatic adjustment value to the initial value. 6. adjustment 6.1 cd adjustment
42 DEH-1100,11 - flow chart 4 3 reset source new test mode 6 [ band band band band band 3 *2 *1 6 6 6 6 1 2 1 2 ] ][ select cd focus mode select focus close/ s curve check crg- auto adjustment display select crg+ rf agc coefficient display/ rough servo and rf agc tracking open tracking open t. close and fit servo ][ 1 3 display 2 3 display or 8x 8x 8x trk sec min 9x 9x 9x trk sec min or crg- crg+ t.balance adjustment *4 f, t, rf agc/ f.bias display select f, t agc and rf agc power on (adjustment for t.offset) *5 *6 *6 *7 crg/tr jump no. select crg+/tr jump+ crg-/tr jump- power off display display display t.close and f,t agc and rf agc and fit servo power on (not adjustment for t.offset) display display 2 power off power off power off 8x 8x 8x trk sec min 9x 9x 9x trk sec min 8x 8x 8x trk sec min 9x 9x 9x trk sec min or 8x 8x 8x trk sec min 9x 9x 9x trk sec min or 00 00 00 trk sec min 99 99 99 trk sec min or 00 00 00 trk sec min 99 99 99 trk sec min or 00 00 00 trk sec min 99 99 99 trk sec min or 91 91 91 trk sec min 0x 0x 0x trk sec min 00 00 00 trk sec min 99 99 99 trk sec min test mode in *3 *1 *3 *6 *2 *5 *7 *4 f.cancel t.offset the original display 1tr/4tr/10tr/32tr/100tr "00", "99" focus close / "01" s.curve 1tr 4tr 91(81) 92(82) crg move 96(86) 100tr 95(85) 32tr 94(84) 10tr 93(83) focus close 00(99) ld off 02 s.curve 01 crg move,100tr jump trk, min, sec f.agc gain t.agc gain f.bias
43 DEH-1100,11 note : the grating angle of the pu unit cannot be adjusted after the pu unit is changed. the pu unit in the cd mecha- nism module is adjusted on the production line to match the cd mechanism module and is thus the best adjusted pu unit for the cd mechanism module. changing the pu unit is thus best considered as a last resort. however, if the pu unit must be changed, the grating should be checked using the procedure below. purpose : to check that the grating is within an acceptable range when the pu unit is changed. symptoms of mal-adjustment : if the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. method : measuring equipment oscilloscope, two l.p.f. measuring points e, f, refout disc abex tcd-784 mode test mode checking procedure 1. in test mode, load the disc and switch the 5v regulator on. 2. using the ] and [ buttons, move the pu unit to the innermost track. 3. press key 3 to close focus, the display should read "91". press key 2 to implement the tracking balance adjust- ment the display should now read "81". press key 3 2 times. the display will change, returning to "81" on the fourth press. 4. as shown in the diagram above, monitor the lpf outputs using the oscilloscope and check that the phase differ- ence is within 75 . refer to the photographs supplied to determine the phase angle. 5. if the phase difference is determined to be greater than 75 try changing the pu unit to see if there is any improvement. if, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. note because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). the angle specified above indicates the aver- age angle. hint reloading the disc changes the clamp position and may decrease the "wobble". f refo e 100k ? 390pf 100k ? 390pf e refo f refo l.p.f. l.p.f. control unit xch ych oscilloscope 6.2 checking the grating after changing the pickup unit
44 DEH-1100,11 grating waveform ech xch 20mv/div, ac fch ych 20mv/div, ac 45 0 75 60 30 90
45 DEH-1100,11 7. general information 7.1 diagnosis 7.1.1 test mode - error messages if a cd is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. this arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) basic indication method 1) when serrorm is selected for the csmod (cd mode area for the system), error codes are written to dmin (min- utes display area) and dsec (seconds display area). the same data is written to dmin and dsec. dtno remains in blank as before. 2) head unit display examples depending on display capability of lcd used, display will vary as shown below. xx contains the error number. 8-digit display 6-digit display 4-digit display error xx err xx e xx or err xx (2) error code list code class displayed error code description of the code and potential cause(s) 10 electricity carriage home ng crg can't be moved to inner diameter. crg can't be moved from inner diameter. failure on home switch or crg move mechanism. 11 electricity focus servo ng focusing not available. stains on rear side of disc or excessive vibrations on rewritable. 12 electricity spindle lock ng spindle not locked. sub-code is strange (not readable). failure on spindle, stains or damages on disc, or excessive vibrations. subcode ng a disc not containing cd-r data is found. turned over disc are found, though rarely. failure on home switch or crg move mechanism. rf amp ng an appropriate rf amp gain can't be determined. cd signal error. 17 electricity setup ng apc protection doesn't work. focus can be easily lost. damages or stains on disc, or excessive vibrations. 30 electricity search time out failed to reach target address. crg tracking error or damages on disc. a0 system power supply ng power (vd) is ground faulted. failure on sw transistor or power supply (failure on connector). remarks: mechanical errors are not displayed (because a cd is turned off in these errors). unreadable toc does not constitute an error. an intended operation continues in this case. a newly designed head unit must conform to the example given above. upper digits of an error code are subdivided as shown below: 1x: setup relevant errors, 3x: search relevant errors, 3x: search relevant errors, ax: other errors.
46 DEH-1100,11 - new test mode s-cd plays the same way as before. if an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its cause and time occurred (in absolute time) are displayed. during setup, operational status of the control software (internal ram: cpoint) is displayed. these displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis. (1) shifting to the new test mode 1 turn on the current test mode by starting the reset from the key. 2 select s-cd for the source through the specified procedure including use of the [source] key, and inserting the disc. then, press the [jump mode selector] key while maintaining the regulator turned off. 3 after the above operations, the new test mode remains on irrespective of whether the s-cd is turned on or off. you can reset the new test mode by turning on the reset start. * with some products, the new test mode can be reset through the same operations as that employed for shifting to the stby mode (while maintaining the acc turned off). (2) key correspondence key test mode new test mode (example) power off power on in-play error production band to power on to power off time/err.no. switching (offset adjustment performed) ] fwd-kick ff/tr+ [ rev-kick rev/tr- 1 t.close (agc performed) scan /parameter display switching 2 t.bal adjustment mode /t.open 3 to power on f.close/rf agc/agc (offset adjustment not performed) 6 mode switching auto/manu /t.close (no agc)/jump switching note: eject and cd on/off is performed in the same procedure as that for the normal mode. (3) cause of error and error code code class contents description and cause 40 electricity off focus detected. fok goes low. damages/stains on disc, vibrations or failure on servo. 41 electricity spindle unlocked. fok = low continued for 50 msec. damages/stains on disc, vibrations or failure on servo. 42 electricity sub-code unreadable. sub-code was unreadable for 50 msec. damages/stains on disc, vibrations or failure on servo. 43 electricity sound skipping detected. last address memory function was activated. damages/stains on disc, vibrations or failure on servo. note: mechanical errors during aging are not displayed. the error codes should be indicated in the same way as in the normal mode.
47 DEH-1100,11 (4) display of operational status (cpoint) during setup status no. contents protective action 01 carriage move to home position started. none 02 carriage is moving toward inner diameter. specified 10 seconds has been passed or failure on home switch. 03 carriage is moving toward outer diameter. specified 10 seconds has been passed or failure on home switch. 05 carriage outer diameter feed (1 second) in progress. none 11 setup started. none 12 spindle rotation and focus search started. none 13 waiting for focus close (xsi = low). specified focus search time has been passed. 14 waiting for focus close (fok = high). (after agc) specified focus search time has been passed. 15 waiting for focus close (fok = high). (before agc) specified focus search time has been passed. 16 rough agc in progress. off focus. 17 setup (1/2) before t balance adjustment is started. off focus. 18 setup (2/2) before t balance adjustment is started. off focus. 24 t balance adjustment (1/2). off focus. 25 t balance adjustment (2/2). off focus. 26 standing by after spindle rough servo is over. off focus. 27 setup before rf agc (first) is started. off focus. 28 rf agc (first) in progress. off focus. 29 setup before rf agc (second) is started. off focus. 30 rf agc (second) in progress. off focus. 31 tracking close in progress. off focus. 32 standing by after tracking is closed. off focus. 33 focus agc started. off focus. 34 focus agc in progress. tracking agc started. off focus. 35 tracking agc in progress. off focus. spindle processes applicable servo. 36 check of mirr and lock pin. rf agc in progress. off focus. spindle not locked. crg close in progress. check of sub-code. sub-code unreadable. (5) display examples 1) during setup (when status no. = 11) trk no. min. sec. 11 11' 11" 2) during operation (toc read, trk search, play, ff and rev) the same as in the normal mode. 3) when a protection error occurred switch to the following displays (a) and (b) using the [band] switch: (a) error occurrence timing display in absolute time. an example: error occurred in 12th tune at 34'56" in absolute time. trk no. min. sec. 12 34' 56" (b) error no. display an example: error #40 (off focus is detected) error-40
48 DEH-1100,11 7.1.2 disassembly - removing the tuner amp assy remove the two screws (fig.2). remove the three screws and then remove the cover (fig.2). remove the screw (fig.3). disconnect the four claws and then remove the tuner amp assy (fig.3). - removing the upper case (not shown) - removing the cd mechanism module (fig.1) remove the four screws. disconnect the connector and then remove the cd mechanism module (not shown). - removing the grille assy (not shown) 1.disconnect the two stoppers and then remove the grille assy. fig.1 fig.2 fig.3 tuner amp assy cover cd mechanism module
49 DEH-1100,11 - removing the upper frame 1. remove six springs a, two springs b and four screws. 2. remove two tabs situated on rear side of the upper frame, remove two arms on the front side, then remove two tabs on the front side. - removing the carriage mechanism 1. disengage the carriage mechanism from the two dampers situated in the front side by driving it up, then disengage and remove the mechanism from the one damper by driving it up aslant into front side direction. note : when assembling the carriage mechanism, coat the dampers with alcohol prior to the assembly. - removing the clamp arm assy 1. remove a spring a, a b and a spring c. 2. drive the clamp arm assy up into rear side direction, then disengage the arm from its current position finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward right side to remove it. b a b a a a arm arm a b c upper frame carriage mechanism section clamp arm assy section a a
50 DEH-1100,11 - removing the guide arm assy 1. remove a connector, a spring a and b 2. drive the guide arm assy up aslant into rear side direction, then remove it from a pin. finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward left side to remove it. note : when assembling the guide arm assembly, route the cord inside the assembly. in this operation, care must be exercised so that cord may be caught by the gear. - removing the lo arm assy 1. remove two pins to dismount the lo arm assy. - removing the control unit and the spindle motor 1. remove from the connector after mounting the short pin on the flexible pcb of the pickup unit. 2. remove two soldered joints, then remove two screws a. 3. remove two connectors and a screw b. 4. disengage the control unit from two tabs, then dis- mount the unit by sliding it toward left. 5. dismount the spindle motor. a guide arm assy section b pin lo arm assy section spindle motor a a control unit short pin b
51 DEH-1100,11 - removing the loading motor and carriage motor 1. remove the spring and two screws a. 2. dismount the loading motor. 3. remove the belt, a screw b, two screws c, a guide and a screw unit. 4. dismount the carriage motor. note : when assembling the belt, use care so that it may not be contaminated by grease. - removing the pickup unit 1. remove two screws and a shaft. 2. dismount the pickup unit. pickup unit shaft c guide b screw unit carriage motor a a c belt loading motor
52 DEH-1100,11 7.2 parts 7.2.1 ic - pin functions(pe5091a) pin no. pin name i/o format function and operation 1 model1 i model select input 2 nl1 i noise level input 3 nl2dt i noise level input 2 4 avss a/d gnd 5 st i stereo input 6 sd i sd signal input 7 aref1 (d/a converter standard voltage) 8 kydt i key data input 9 dpdt o c key data output 10 sdbw i sdbw input 11 tunpdi i pll ic data input 12 tunpdo o c pll ic data output 13 tunpck o c pll ic clock output 14 tunpce o c pll ic chip enable output 15 nc not used 16 xsi i c lsi data input 17 xso o c lsi data output 18 xsck o c lsi clock output 19 drst o c rds decoder reset output 20 adpw o c a/d converter power output 21 nc not used 22 vdcont o c vd power control output 23 cont o c servo driver power control output 24 xao o c cd lsi data discernment control signal output 25 xrst o c cd lsi reset output 26 xstb o c cd lsi strobe output 27 clamp i disc clamp sense input 28 mirr i mirror detection input 29 fok i focus ok signal input 30 lock i spindle lock detector input 31 cdload o c load motor loading control output 32 telin i cellular mute input 33 vss gnd 34 cdeject o load motor eject control output 35 cd5von o c cd +5v power supply control output 36 40 nc not used 41 swvdd o c grille power supply control output 42 syspw o c system power supply control output 43 nc not used 44 mute o c mute output 45 pee o c beep tone output 46 loch o c loch output 47 rds57k i 57khzbp-out sense input 48 tunpce2 o c eeprom chip enable output 2 49 nc not used 50 vck o c clock output for electronic volume 51 vdt o c data output for electronic volume 52 antpw o c antenna power output 53 vst o c strobe pulse output for electronic volume 54 57 deq4-1 o c direct eq data output 4-1 58, 59 nc not used 60 reset reset 61, 62 nc not used 63 asens i acc power sense input
53 DEH-1100,11 pin no. pin name i/o format function and operation 64 bsens i back up power sense input 65 dsens i grille detach sense input 66 tmute o c tuner mute output 67 locl o c loc l output 68 vdd power supply 69 x2 crystal oscillator connection pin 70 x1 crystal oscillator connection pin 71 ic gnd 72 nc not used 73 testin i test program mode input 74 avdd positive power supply terminal for analog circuit 75 avref0 gnd 76 sl i signal level input 77 temp i temperature detector input 78 vdsens i over voltage sense input 79 dscsns i disc detect input 80 ejtsns i disc eject position detect input 80 1 20 21 40 41 60 61 *pe5091a output format meaning c c mos output ic's marked by* are mos type. be careful in handing them because they are very liable to be damaged by electrostatic induction. s-80834any 1 2 3 1 out vdd vss br9010fv nc vcc cs sk wc gnd do di 1 2 3 4 8 7 6 5 cs sk di do wc : chip select input : serial data clock input : serial data input : serial data output : write control input *pd6293a 49 48 33 32 17 16 1 64
54 DEH-1100,11 sn761029dl 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 vcc avcc in1-r in1-l in2-r in2-l in3-r in3-l in4(+)-r in4(+)-l in4(-)-r in4(-)-l agnd agnd swout-r swout-l zcin-r zcin-l loud-r loud-l vrin-r vrin-l treb-r treb-l bass-c1-r bass-c1-l bass-r-r bass-r-l bass-c2-r bass-c2-l nc nc toneout-r toneout-l faderin-r faderin-l frntout-r frntout-l rearout-r rearout-l dvcc vrefin data agnd clk dgnd stb ct 3 line serial bus bass treble volume, loudness fader gain adjust isolator zero-cross detector power supply bass treble volume, loudness fader gain adjust isolator power supply a a - pin functions (pd6293a) pin no. pin name i/o function and operation 1-5 seg4-0 o lcd segment output 6-9 com3-0 o lcd common output 10 vlcd lcd drive power supply 11-14 kst3-0 o key strobe output 15,16 kdt0,1 i key data input (analogue input) 17 rem i remote control reception 18 dpdt i display data input 19 nc not used 20 kydt o key data output 21 moda gnd 22 x0 crystal oscillator connection pin 23 x1 crystal oscillator connection pin 24 vss gnd 25,26 kdt2,3 i key data input 27 nc not used 28 kst4 o key strobe output 29-32 nc not used 33-55 seg35-13 o lcd segment output 56 vdd power supply 57-64 seg12-5 o lcd segment output
55 DEH-1100,11 - pin functions (upd63711gc) pin no. pin name i/o function and operation 1 d.gnd logic circuit gnd 2 rfok o rfok signal output 3 rst i reset signal input 4 a0 i command/parameter identification signal input 5 stb i data strobe signal input 6 sck i clock signal input for serial data input/output 7 so o serial data and status signal output 8 si i serial data input 9 xtalen i crystal oscillation control pin 10 d.vdd positive power supply terminal to logic circuit 11 da.vdd positive power supply terminal to d/a converter 12 r_out o right channel audio output signal 13 da.gnd d/a converter gnd 14 regc i the outside putting capacitor connection pin for scf regulator 15 da.gnd d/a converter gnd 16 l_out o left channel audio output signal 17 da.vdd positive power supply terminal to d/a converter 18 r+ o right channel audio data output 19 r- o right channel audio data output 20 l- o left channel audio data output 21 l+ o left channel audio data output 22 x.vdd positive power supply terminal to crystal oscillation circuit 23 xtal i crystal oscillator connect pin 24 xtal o crystal oscillator connect pin 25 x.gnd crystal oscillation circuit gnd 26 d.vdd positive power supply terminal to logic circuit 27 emph o output pin for the pre-emphasis data in the sub-q code 28 flag o flag output pin to indicate that audio data currently being output consists of noncorrectable data 29 din i serial data input to internal dac 30 dout o serial audio data output 31 sckin i serial clock input to internal dac 32 scko o audio data that is output from dout changes at rising edge of this clock 33 lrckin i lrck signal input to internal dac 34 lrck o signals to distinguish the right and left channels of the audio data output from dout 35 hold o defect detection output 36 tx o digital audio interface data output 37 d.gnd logic circuit gnd 38 c16m o oscillator clock buffering output 39 limit i status of the pin is output at bit 5 of the status output 40 d.vdd positive power supply terminal to logic circuit 41 lock o efm synchronous detection signal 42 rfck o frame synchronous signal of xtal-system 43 mirr o mirr output 44 plck o monitor pin of bit clock 45 d.gnd logic circuit gnd 46 c1d1 o output pin for indicating the c1 error correction results 47 c1d2 o output pin for indicating the c1 error correction results 48 c2d1 o output pin for indicating the c2 error correction results 49 c2d2 o output pin for indicating the c2 error correction results 50 c2d3 o output pin for indicating the c2 error correction results 51 d.vdd positive power supply terminal to logic circuit 52 pack o cd-text pack synchronous signal 53 tso o cd-text data serial output 54 tsi i cd-text control parameter serial input 55 tsck i cd-text serial clock input 56 tstb i cd-text parameter strobe signal input 57 d.gnd logic circuit gnd
56 DEH-1100,11 pin no. pin name i/o function and operation 58 test0 i test pin 59 test1 i test pin 60 atest o test pin 61 a.gnd analog circuit gnd 62 fd o focus drive output 63 td o tracking drive output 64 sd o sled drive output 65 md o spindle drive output 66 dac0 o dac output for adjustment 67 dac1 o dac output for adjustment 68 dac2 o dac output for adjustment 69 dac3 o dac output for adjustment 70 a.vdd positive power supply terminal to analog circuit 71 efm o efm signal output 72 asy i efm comparator reference voltage input 73 c3t 3t detection capacitor additional pin 74 rfi i rf signal input for efm data regulation 75 agco o rf signal output of after gain adjustment 76 agci i rf-agc amplifier input 77 rfo o rf summing amplifier output 78 eq2 rf amplifier equalizer parts additional pin 79 eq1 rf amplifier equalizer parts additional pin 80 rf- i rf summing amplifier inverted input 81 a.gnd analog circuit gnd 82 a i photo detector a input 83 c i photo detector c input 84 b i photo detector b input 85 d i photo detector d input 86 f i photo detector f input 87 e i photo detector e input 88 a.vdd positive power supply terminal to analog circuit 89 refout o reference electric potential output 90 fe- i focus error amplifier inverted input 91 feo o focus error amplifier output 92 te- i tracking error amplifier inverted input 93 teo o tracking error amplifier output 94 te2 o tracking error output of after amplification 95 tec i tracking comparator input 96 a.gnd analog circuit gnd 97 pd i pd detection signal input for ld output monitor 98 ld o ld control current output 99 pn i apc circuit control polarity set pin 100 a.vdd positive power supply terminal to analog circuit 20 21 40 41 60 61 80 1 100 76 26 1 25 75 51 50 *upd63711gc
57 DEH-1100,11 - pin functions (ba5985fm) pin no. pin name i/o function and operation 1 fwd i loading driver fwd input 2 opin1( + ) i ch1 pre-amplifier input 3 opin1( ? ) i ch1 pre-amplifier inverted input 4 opout1 o ch1 pre-amplifier output 5 opin2( + ) i ch2 pre-amplifier input 6 opin2( ? ) i ch2 pre-amplifier inverted input 7 opout2 o ch2 pre-amplifier output 8 vcc power supply 9 vol( ? ) o loading driver negative output 10 vol( + ) o loading driver positive output 11 vo2( ? ) o driver ch2 negative output 12 vo2( + ) o driver ch2 positive output 13 vo1( ? ) o driver ch1 negative output 14 vo1( + ) o driver ch1 positive output 15 vo4( + ) o driver ch4 positive output 16 vo4( ? ) o driver ch4 negative output 17 vo3( + ) o driver ch3 positive output 18 vo3( ? ) o driver ch3 negative output 19 gnd gnd 20 bias i bias input 21 mute mute control 22 opout3 o ch3 pre-amplifier output 23 opin3( ? ) i ch3 pre-amplifier inverted input 24 opin3( + ) i ch3 pre-amplifier input 25 opout4 o ch4 pre-amplifier output 26 opin4( ? ) i ch4 pre-amplifier inverted input 27 opin4( + ) i ch4 pre-amplifier input 28 rev i loading driver rev input ba5985fm
58 DEH-1100,11 7.2.2 display - caw1560 common segment
59 DEH-1100,11 7.3 operational flow chart vdd=5v 68pin power on l l yes l bsens 66pin asens 65pin dsens 63pin adpw h 20pin swvdd l 41pin source keys operative to each source's flow chart syspw h 42pin starts communication with grille microcomputer. source on 300ms 300ms in case of the above signal, the communication with grille microcomputer may fail. if the time interval is not 300msec, the oscillator may be defective.
60 DEH-1100,11 8. operations and specifications 8.1 operations +/?button eject button buttons 1? local button bsm button audio button band button disc loading slot clock button source/off button loud button 5 / / 2 / 3 buttons
61 DEH-1100,11 a title (english) basic operation to listen to music the following explains the initial operations required before you can listen to music. note: loading a disc in this product. 1. select the desired source (e.g. tuner). each press of the source/off button selects the desired source in the following order: built-in cd player = tuner note: when no disc is set in this product, built-in cd player source will not change. when this products blue/white lead is connected to the cars auto-antenna relay control terminal, the cars auto-antenna extends when this products source is switched on. to retract the antenna, switch the source off. 2. raise or lower the volume. 3. turn the source off. hold for 1 second each press changes the source ... basic operation of tuner a title (english) manual and seek tuning you can select the tuning method by changing the length of time you press the 2 / 3 button. manual tuning (step by step) 0.5 seconds or less seek tuning 0.5 seconds or more note: if you continue pressing the button for longer than 0.5 seconds, you can skip broadcast stations. seek tuning starts as soon as you release the button. stereo indicator ? ?lights when a stereo station is selected. preset tuning you can memorize broadcast stations in buttons 1 through 6 for easy, one-touch station recall. preset station recall 2 seconds or less broadcast station preset memory 2 seconds or more note: up to 18 fm stations (6 in fm1, fm2 and fm3) and 6 am stations can be stored in memory. you can also use the 5 or buttons to recall broadcast stations memorized in buttons 1 through 6. preset number indicator band fm1 = fm2 = fm3 = am band indicator frequency indicator
62 DEH-1100,11 a title (english) basic operation basic operation of built-in cd player track number indicator play time indicator eject note: the cd function can be turned on/off with the disc remaining in this product. ? a disc left partially inserted after ejection may incur damage or fall out. track search and fast forward/reverse you can select between track search or fast forward/reverse by pressing the 2 / 3 button for a different length of time. track search 0.5 seconds or less fast forward/reverse continue pressing note: if a disc cannot be inserted fully or playback fails, make sure the recorded side is down. push the eject button and check the disc for damage before reinserting it. if a disc is inserted with the recorded side up, it will be ejected automatically after a few moments. if the built-in cd player cannot operate properly, an error message (such as ?rror-14? appears on the display. disc loading slot note: the built-in cd player plays one standard 12 cm or 8 cm (single) cd at a time. do not use an adapter when playing 8 cm cd. a title (english) audio adjustment entering the audio menu with this menu, you can adjust the sound quality. note: after entering the audio menu, if you do not perform an operation within about 30 seconds, the audio menu is automatically canceled. 1. select the desired mode in the audio menu. 2. operate a mode. 3. cancel the audio menu. each press changes the mode ...
63 DEH-1100,11 a title (english) audio adjustment audio menu functions the audio menu features the following functions. balance adjustment (fader) this function allows you to select a fader/balance setting that provides ideal listening con- ditions in all occupied seats. 1. press the audio button and select the fader/balance mode (fader) in the audio menu. note: fader ??is the proper setting when 2 speakers are in use. bass adjustment (bas) you can adjust a bass level as desired. 1. press the audio button and select the bass mode (bas) in the audio menu. 2. boost or attenuate the bass level with the 5 5 / buttons. the display shows ?6??6? 3. adjust left/right speaker bal- ance with the 2 2 / 3 3 buttons. ?9???9?is displayed as it moves from left to right. 2. adjust front/rear speaker bal- ance with the 5 5 / buttons. ?15???15?is displayed as it moves from front to rear. treble adjustment (tre) you can adjust a treble level as desired. 1. press the audio button and select the treble mode (tre) in the audio menu. loudness adjustment (loud) the loudness function compensates for deficiencies in the low and high sound ranges at low volume. ?oud switch the loudness function on/off with the loud button. 2. boost or attenuate the treble level with the 5 5 / buttons. the display shows ?6??6?
+ + ++ ++ connection diagram this product rear output antenna jack fuse black (ground) red yellow to terminal always supplied with power regardless of ignition switch position. to electric terminal controlled by ignition switch (12 v dc) on/off. to vehicle (metal) body. with a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. perform these connections when using a different amp (sold separately). to system control terminal of the power amp or auto-antenna relay control terminal. (max. 300 ma 12 v dc.) connecting cords with rca pin plugs (sold separately) blue/white system remote control power amp (sold separately) white white/black green green/black gray gray/black violet violet/black front speaker rear speaker right rear speaker rear speaker front speaker rear speaker left 64 DEH-1100,11
65 DEH-1100,11 8.2 specifications general power source .......... 14.4 v dc (10.8 ?15.1 v allowable) grounding system ........................................ negative type max. current consumption ...................................... 10.0 a dimensions (din) (chassis) ...... 178 (w) 50 (h) 159 (d) mm [7 (w) 2 (h) 6-1/4 (d) in] (nose) ............ 188 (w) 58 (h) 19 (d) mm [7-3/8 (w) 2-1/4 (h) 3/4 (d) in] (d) (chassis) ...... 178 (w) 50 (h) 164 (d) mm [7 (w) 2 (h) 6-1/2 (d) in] (nose) ............ 170 (w) 48 (h) 14 (d) mm [6-3/4 (w) 1-7/8 (h) 1/2 (d) in] weight ........................................................ 1.4 kg (3.1 lbs) amplifier continuous power output is 17 w per channel min. into 4 ohms, both channels driven 50 to 15,000 hz with no more than 5% thd. maximum power output ...................................... 40 w 4 load impedance .......................... 4 ? (4 ?8 ? allowable) preout maximum output level/ output impedance .................................... 2.2 v/1 k ? tone controls (bass) .............................................. 12 db (100 hz) (treble) ............................................ 12 db (10 khz) loudness contour ........ +10 db (100 hz), +7 db (10 khz) (volume: ?0 db) cd player system .................................... compact disc audio system usable discs .................................................. compact disc signal format .................... sampling frequency: 44.1 khz number of quantization bits: 16; linear frequency characteristics .............. 5 ?20,000 hz (1 db) signal-to-noise ratio ...... 94 db (1 khz) (ihf-a network) dynamic range ............................................ 92 db (1 khz) number of channels ............................................ 2 (stereo) fm tuner frequency range .................................... 87.9 ?107.9 mhz usable sensitivity .................................................... 10 dbf (0.9 v/75 ? , mono, s/n: 30 db) 50 db quieting sensitivity .... 15 dbf (1.5 v/75 ? , mono) signal-to-noise ratio ...................... 70 db (ihf-a network) distortion .......................... 0.3% (at 65 dbf, 1 khz, stereo) frequency response ...................... 30 ?15,000 hz (3 db) stereo separation .......................... 40 db (at 65 dbf, 1 khz) selectivity .................................................... 70 db (2aca) three-signal intermodulation (desired signal level) ........................................ 30 dbf (two undesired signal level: 100 dbf) am tuner frequency range ...................... 530 ?1,710 khz (10 khz) usable sensitivity .............................. 18 v (s/n: 20 db) selectivity ................................................ 50 db (10 khz) note: specifications and the design are subject to possi- ble modification without notice due to improve- ments.

▲Up To Search▲

Price & Availability of DEH-1100

	To Download DEH-1100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .